SP-1 V4 Inertia Electronic Kit

870.00995.00

Software and electronics kit for inertial dyno.
(includes 16T geartooth)

Features:

  • Dyno operation controlled by on dyno button, or from the computer
  • Real time on screen display test results. Tests appears in the screen while the engine accelerates.
  • See graphs simultaneously: show or hide any curve.
  • Really accurate and detailed curves: see engine failures easily.

Software: SportDyno 4.0 FeaturesDownload

(Price for DAQ only: 870€)

*Prices do not include VAT

What is new in V4?

  • More connectors and analog channels:
  • 2 thermocouple inputs (in the front)
  • 4 analog inputs (at rear)
  • 2 counter inputs
  • servo output (available under request)
  • additional engine rpm input (0 to 5 volt), suitable to be connected to ECU output or inductive clamp adaptor.

What is new in V3?

  • Enhanced engine RPM input circuit. Hi sensibility for traditional ignition and new ignitions (on-spark coils). Noise protection.
  • 2 General purpose analog inputs 0-5v, suitable for lambda probe

Easy to use

SP-1 data acquisition unit (V4)
with 8 input channels:

  • Engine rpm input
  • 2 thermocouple type K input (up to 1000°C)
  • 4 general analog inputs
  • 2 counter inputs (available under request)
  • 2 servo outputs (available under request)

And sensors:

  • Hall Effect Digital Sensor for measuring roller speed
  • Capacitive pickup to measure engine rpm
  • Installation cables and SportDyno software

Connection is done by using PC serial port, this makes very easy to connect this unit to any computer.

NOTE: Most laptopts do not have a serial port, but a FTDI serial-USB adaptor is provided to connect SP1 on this PCs. This adaptor creates a virtual COM port that can be selected on the program to work with the unit as usual. Theorically any RS232-USB adaptor will work with this device, requeriments are 115,200 baud transfer. We can supply a well-tested adaptor if you can not find a suitable one.

The equipment is completed with a modern Software for Windows, very powerful and easy to use. It allows to work simultaneously with several tests.

Specifications

Power supply: 85-240V AC, 50/60 Hz

Data transfer: 115200 baud RS232C (DB9 Conn). USB FTDI Adapter is included with the kit

Roller rpm input connector (CN2)

  • Type of sensor: Hall Effect active sensor (doesn’t need external magnets)
  • Type of input: logical Level (active at high level)
  • Maximum frequency: 15 KHz (6,000 rpm with 150 teeth)
  • Maximum cable length: 6m
  • Run/Stop input SWITCH

Engine rpm input: capacitive type (reads high voltage pulses on ignition cables)

Display: LCD 16×2 Characters.

Installation

Installation and Connections V4

Dynamometer Installation V4:

CN1-additional engine RPM input, 0 to 5 volt. Suitable for ECU output, or external adaptors.

CN2-Roller Speed Sensor (Hall Effect), and Switch input

CN3-Load Cell, not available at SP1

CN4-Digital Counters and Servo outputs, available in next version 4b

CN5-Analog connector, Analog channels 1 and 3 (J and L), from 0 to 5 volt, suitable for Wideband Oxigen Sensor

CN6-Analog connector, Analog channels 2 and 4 (K and M), from 0 to 5 volt, suitable for Wideband Oxigen Sensor

Dynamometer Installation V3:

CN1- general purpose input. (lambda probe)

At CN1 connector are available two analog channels (input from 0 to 5volt) that can be used to connect a lambda probe such as Bosch LSM11.

CN2- pickup connection. pick-up should be mount close the geared tooth. Maximum frequency of teeth should not be greather than 15 Khz, so the gear teeth will be max of 150 teeth (for 6,000 rpm of roller).

Start/Stop Button on CN2 to control the dynamometer operation.

What implements

SP1 / SP1+ SP5 2WD / AWD SP6 2WD / AWD / HUB-4
Roller Channels 1 2 4
Engine Channel 1 1 1
Analog Channels (0-5V) 4 6 8
Thermocouples (K) 2 8 8
Counter input (knock) 1 1 1
Load Cell Channels 0 / 1 (24 bit) 2 (24 bit) 2 / 2 / 4 (24 bit)
Brake Outputs – / 1 2 4
Servo Output 1 RC* 1 RC or PWM 1 RC or PWM
Airspeed Output – / 1 PWM 1 PWM 1 PWM
Relay Outputs 8 8
Speed Control (PID) – / 1 2 / 2 + sync 2 / 2 + sync / 4 + sync
RS232 1 1 2
Bluetooth 1 1* 1*
Ethernet 1 1
CANBUS 1 2
KIT Price 995 / 1995 2995 / 3995 3495 / 4495 / 6495
DAQ Price 870 / 1195 2295 2795

What contains

SP1 / SP1+ SP5 2WD / AWD SP6 2WD / AWD / HUB-4 Price
Hall sensor 1 1 / 2 1 / 2 / 4  60€
Capacitive Clamp 1 1 1  30€
Inductive clamp – / 1 1 1  80€
Load Cell – / 1 1 / 2 1 / 2 / 4  150€
Brake Power Supply – / 1 1 / 2 1 / 2 / 4  650€
USB-Serial 1 1 1  25€
Power Cord 1 1 1  10€
Ground Cable 1 1 1  10€
Pendrive 1 1 1
Price 995 / 1995 2995 / 3995 3495 / 4495 / 6495